This lets you preset the satellite to its correct elevation. Mount the mast, or pole, for the receiver. Multiple options exist for this step depending on where you install the dish roof, hollow wall, on brick or concrete, etc. Consult the self-installation guide to see instructions and the necessary tools for each option. Make sure the mast is level to get a satellite signal. Use a bubble level to help you determine it is even. Put the satellite receiver dish on its mast.
Attach the LNB to the receiver's support arm. Position a grounding block as closely as you can to the place where the dish's cable will run into the house. Run the receiver dish's cable to the grounding block. The connection to the block binds the dish to an acceptable grounded point in the main building ground, such as an enclosure for electrical service equipment or a metallic service raceway.
Run the RG-6 coaxial cable to the back of the receiver inside the house. The RG-6 cable should also be connected to the grounding block. Make sure a landline phone is off its hook to avoid getting an electric shock from any incoming calls. Connect the receiver to a phone jack with the phone line. Check for a signal using the "Dish Pointing" menu's signal meter displayed on your TV screen. Adjust the dish's pointing to achieve your maximum signal strength.
It depends on the connector on your surround sound system and your receiver sound. You will need to buy a wire that has a port compatible with your receiver in one end and with your sound system on the other end.
Yes No. Not Helpful 1 Helpful 2. It depends on what you call a pole. The cover is a pretty snug fit, but with the sealant, no water is getting in there.
The Control Module is in one of those small boxes listed at the beginning. There are a few ports on the back, but only two you should care about: The six-port data plug and the power. Plug in the data cable, it has to go in correctly so line up the holes with the plugs, and push it in firmly. Next plug in the power cable, then at the other end of the power brick, plug it into power. When you first turn on the control module, press and hold it for a few seconds.
If you press it and release right away, it will turn on briefly, then shut off. When it turns on, it will start up the motor for the base up on the roof and begin searching for a signal.
Now when you get to a campground, all you have to do is turn on the control module and it will automatically begin searching for a signal from a satellite.
In our case, it never found one. This is not a slight against Winegard though as we are parked under several trees. If we were more out in the open, I have no doubt it would be able to find a signal. Always remember to shut off the dish and make sure it has folded back down into position before you travel. You do not want to driving around with a dish sticking up as it will cause wind resistance could tear off, as well as increasing your height profile.
In the Box Inside the box is the base mechanism and arm for the dish, the dish unattached for shipping , three boxes, a bag of hardware, a 30 foot coax cable, and a packet of instructions. Like this: Like Loading Written by eric Eric is a dedicated technophile and strives to make things in Sleipnir as innovative, simple to use, and convenient as possible. He has worked a variety of jobs, from construction and manufacturing to working as a civilian in a law enforcement agency.
He is an avid tabletop gamer and builds websites in his spare time. October 14, eric 0. Off the Grid Technology Uncategorized. October 07, eric 0. Off the Grid Technology. It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place. You may need to loosen the LNB later to readjust it and improve the signal quality. Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open end of the support.
If everything is attached correctly, it will fit inside or behind the adjustment panel. You can then add the 1 or 2 remaining bolts to fasten these pieces together. If the dish looks good, then you're ready to position it to communicate with a satellite. If the mount is meant to attach to the back of the panel, your satellite will also come with a pair of clips. Position them behind the support, then add the screws through them to bind the parts together.
Part 3. Select a satellite you wish to connect to. Pick a satellite that is in range of your particular dish. There are numerous satellites out there, but dishes cannot get signals from all of them. If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites.
Tracking sites list the names, which usually include the owning company or the service they provide. If you bought a satellite service, it is possible to receive satellite signals outside that service. Since you usually need to replace several parts, it's easier to get a new satellite instead.
Try to pick a satellite close to your area. If you subscribe to a particular TV service, you will need to use the company's satellites. The biggest providers have multiple satellites. Find the satellite's location before positioning the dish. You're going to need to point the dish in the correct direction, then angle it up at the sky.
This isn't easy to do if you don't know the satellite's positioning. Fortunately, satellites don't move much, so you can use a positioning database to adjust your dish.
The site will give you the precise positioning needed for your dish to receive the signal. You won't be able to receive a signal from a distant satellite. Don't expect to reach a Chinese satellite if you're in North America, for instance. Use the azimuth number to rotate the satellite.
Have a compass handy and locate true north first. Then, look at the azimuth number and find where that is on the compass. North is considered 0 degrees, east is 90 degrees, south is degrees, and west is degrees. Rotate the satellite dish horizontally until it points in the correct direction. Then, turn the satellite southwest from there. Move the dish vertically to adjust its elevation. Once you know the height needed to reach the satellite, go behind the dish.
Examine the end of the mount where it connects to the dish. You will see a bolt inside a slot labeled by degrees, usually 10 to Loosen the bolt by twisting it counterclockwise, then reposition the dish to the proper elevation. Moving the bolt along the slot raises or lowers the dish. For instance, if the dish requires a degree elevation, it will point up into the sky almost as much as it possibly can.
Slide the loosened bolt back toward the degree marker. Adjust the dish's polarization until you get a clear signal.
The final part that needs to be adjusted is LNB, responsible for receiving and sending the signal into your home. It is usually an arm on the front that points toward the dish. Test out the signal quality by hooking the dish up to the receiver and a TV, then loosen the connecting nut on the arm by turning it counterclockwise with a wrench.
If the TV is far away, have someone else stand near it and give you feedback. You may need to wait to adjust the LNB until you're done with the wiring. Take care of it before then, if you're able, so you don't have to keep climbing on the roof to make adjustments. The LNB can sometimes be controlled by turning a mount part on the back of the dish left or right.
Part 4. Check your home first for a previously-used cable opening. The dish's cable needs its own little space to enter your home and hook up to your TV. Unless your home is in the process of being built, drilling a single hole is the easiest way to do this. Position your TV and the satellite receiver nearby to prepare for the connection. It needs to be below the frost line, the lowest point that freezes in winter, which is about 3 in 7.
The satellite dish installers on our team are second to none. Let us match you with a local satellite dish installer. The satellite installers in our network are more than just electrical contractors. These hardworking folks are our partners. We proud to recommend any and all of our local satellite installers.
0コメント