Pintuck Foot with 2 guides. Place Accessory Adapter over the back two holes of the front cover table. Place the accessory bracket on top of the Accessory Adapter. Raise the telescopic thread guide to its highest position. Rotate the shaft to the left and right until each section "clicks" into a locked position fig.
To open the front table, place your thumb B against the tab, and slide the cover to the right. A slight pull toward you will allow the cover to swing down, providing access. Raise the presser foot lever. This will also lower the feed dogs out of the way. Raise the needles to the highest position. Push the presser foot release lever located at the back of the presser foot holder. Slide the presser foot to the left of the needles.
Slide the foot from the left to right. Align the bar to the foot with the groove in the holder. Lower the presser foot lever to snap into place.
Turn the hand wheel counter clockwise to engage the feed dogs in the up position. The raised markings on the toe of the foot are seam line guides. They indicate the needle positions to help guide your fabric for accurate seaming. A stitch length of 3mm, or about 10 stitches per inch is ideal for most fabrics. For seaming very lightweight fabrics, you may prefer a shorter stitch length. When sewing heavier fabrics, you may choose to lengthen the stitch fig.
Your Baby Lock serger is equipped with differential feed. The set of feed dogs work independently in order to ensure smooth sewing on all fabrics fig. When the differential feed adjusting lever, located at the machine's right, front edge is set on "N" for normal feeding, the feed dogs move the same distance.
This is the setting to use for most fabrics and. When the dial is set above "N", the front feed dog will feed more fabrics than the back.
This is because the front feed dog moves at a greater distance than the back feed dogs. As a result, the fabric becomes compressed or eased, as the diagram on the front cover indicates.
This can eliminate wavy seams in stretchy fabrics or those cut on the bias grain. When the differential feed lever is set below "N" fig. F , the front feed dog moves less distance than the back feed dog. This adjustment stretches the fabric slightly as it is sewn. The lower settings prevent puckers on lightweight fabric fig. The tension settings range from 0 to 9. The fabric and thread that you are working with will deter-. Be sure to sew test after changing the settings. The chain looper dial is color coded blue for easy identification.
The tension settings range from 0. The fabric, thread and stitch that you are working with will determine what the tension set-. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Baby Lock. Read all instructions before using this overlock machine.
Do not use outdoors. Do not use bent needles. If in doubt please contact your retailer for guidance. Welcome to the Baby Lock Cover Stitch Machine Your Baby Lock Cover Stitch machine provides a variety of chain and cover stitches, allowing you to create professional looking hems just like the ready-to-wear fashions in stores. Happy Sewing! O Side Cover Left Needle - C How to Use the Needle Threader Table of Contents Cont. Please read all instructions before using your new machine.
R When forming a chain stitch, the chain needle thread catches the chain looper to form a straight V stitch on the top of your fabric and thread chain loops on the underside. Use 2 or 3 cover stitch I needles and the chain looper to form a double or triple row of straight stitching on the top and a weave of thread on the underside of your fabric. E After setting up your machine for the first time, take a few moments to learn how it sews.
Before W your machine is threaded, turn the handwheel toward you and watch the operation of the various parts. Overview of the Baby Lock 1. Presser foot pressure adjusting screw Machine lock button release lever Differential feed adjusting lever 3.
Machine lock button Left needle tension dial 4. Center needle tension dial 5. Looper threading lever Right needle tension dial 6. Thread cutter Looper tension dial 7. Needle height viewing area Needle drop drawer 8. Needle clamp screw Chain looper threading port 9. Needle plate Telescopic thread guide and antenna Snap-on presser foot Power switch Side cover Attachment screw holes Front table Carrying handle threads.
Stitch length dial. To open, swing the "lid" on the thread spoolstand to the right to reveal the tray holding some of the accessories listed below. Others may E be found in the machine packing materials. These optional accessories are available at your Baby Lock retailer. Accessory Adapter Place Accessory Adapter over the back two holes of the front cover table.
Remove machine from box V E After removing the packing materials from R the box, gently lift your Baby Lock by grasp- ing the handle provided on the top of the V machine. Place the machine on a sewing table or any level surface that provides I ample work area to the left. Place the foot controller in a pedal stay, if desired, and E place it under the sewing table. Plug in the machine A Plug the power cord into the machine first, then into a wall outlet.
The power switch is located toward the back on the right side of the machine. Always make sure the power is off when the machine is not in use fig. Available foot controller for U. Polarized plug This appliance has a polarized plug one blade wider than the other.
To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qual- ified electrician to install the proper outlet. Do not modify the plug in any way. Foot controller The sewing speed of the machine is deter- mined by the amount of pressure applied to the foot controller. When not in use, do not place anything on the foot controller, or the machine could start inadvertently and the controller or motor could burn out.
Setting Up Your Baby Lock 5. Position the telescopic thread guide. Opening Front table To open the front table, place your thumb B against the tab, and slide the cover to the right. A slight pull toward you will allow the cover to swing down, providing access to the chain looper. Side Cover Open side door on the left for easy access to the chain looper thread tray.
Close door before sewing. Thread Cutter O V There is a thread cutter located on the left side of your machine. At E the end of a seam, sew off the fabric edge and continue sewing to R create a 5 - 6 inch 12 - 15cm thread chain.
Bring the chain of thread up and back and pull forward into the V thread cutter. You may find it necessary, however, to decrease the pressure for thick fabrics or increase pressure for thin fabrics to feed more smoothly under the foot.
Use a coin to turn the screw on top of the machine. To increase pressure, turn the pressure adjusting screw clockwise. To decrease pressure, turn the screw counterclockwise. Snap-On Presser Foot. Presser Foot Release Lever. The Baby Lock has the convenience of a snap-on presser foot. Question 2-Straight stich middle position-needle does NOT go to middle, but to the left.
How do I change it? View the manual for the Baby Lock Ellegante here, for free. This manual comes under the category Sewing machines and has been rated by 2 people with an average of a 9. This manual is available in the following languages: English. Below, you will find the most frequently asked questions about the Baby Lock Ellegante.
Is your question not listed? Ask a question. Answer this question Send. Sandi Andreas, No comments 0. Baby Lok Manual downloadable???? Judy, No comments 0. What class bobbins does it use? Dorothy, No comments 0. How are presser feet attached?
About the Baby Lock Ellegante. Baby Lock Ellegante specifications. Related product manuals.
0コメント